Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Lazyeight

Pages: [1] 2 3 ... 6
Today, 9-25-2020 Tour MFC0015 was. Completed by pilot Buddy Nix #MFC0071.  Boy, am I happy that one is over.  Fun flights but several very difficult landings. 

Misty Flying Club and Multi Player / Re: No flights are available
« on: September 21, 2020, 10:31:05 PM »
Thanks guys. Write this one off to old age.  I was thinking about this after I wrote the first message and figured out what my mistake was.  Jeff, great to hear from you. Yep, I am back flying with RTMM.  Maybe we can get in a flight together one day.

Cheers folks. RTMM is the greatest!

Lazyeight. (Buddy Nix)

Misty Flying Club and Multi Player / No flights are available
« on: September 21, 2020, 04:52:47 PM »
I just completed MFC0014 and ready to fly some other flights. All I see for other flights is not available.
Have I done something wrong? I have been away for some time and have been busy catching up. Lots of fun with this scenery and enjoying learning all the places we have available. You designers at RTMM have done a fantastic job. Really enjoying getting back to this flying!!


Tour MFC0014 Completed 9-21-20 By Lazyeight (Buddy Nix)

General Discussion / Re: New Orbx FTX Central
« on: August 10, 2019, 11:39:45 AM »
My first shot at installing Orbx FTX Central seemed to work fine. Everything opened up faster than in the past and solid FPS speeds. Then I noticed none of my RTMM scenery was showing. So, I began looking at insertion points. Then trouble began. My P3Dv 4.5 would not even open. After trying various changes nothing worked. I deleted ORBX Central and went back to FTX Central and it seems to be doing fine. I would like to use the new ORBX Central when I figure it out. Thanks


Misty Flying Club and Multi Player / Beecher Pass Cabin
« on: March 14, 2019, 12:59:02 PM »
I just flew the 2nd leg of MFC0014 SPB(68A) to BEPA (Beecher Pass Cabin)  As I taxied up to finish the flight all I could see at the spot was campfire smoke. There was no other scenery. As I continued to taxi closer my P3D v4.4 crashed. I have done a little searching for information on this cabin and find very little information. I have the coordinates to begin the flight for the next leg but was just wondering what I need to install and or correct to see this site properly.  Thanks for any help you can offer.

Misty Flying Club and Multi Player / Re: MFC Tour Completions
« on: January 20, 2019, 08:36:04 AM »
Completed Tour MFC0007 Short Fields-BC Interior. Completed 1-19-2019 by Buddy Nix MFC0071

Norm, Saturday afternoon and I had a few minutes to give it a shot and no go. Still airplane is not on the ground.

This morning I loaded up the Barnstorming flight MFC0005. I loaded in the Beaver Amphib at 5KE which is a water landing. I taxied out to the water area and shut down the engine. Opened Cigar Box and all looked fine. Clicked Start Flight and get a message that "Airplane is not on the ground" I shut everything down and ran the FTX Central 3 opened settings and ran Configure FTX Global Vector thinking the elevation was off. Fired up P3Dv4 and set up the flight again. Airplane not on the ground. I went ahead and flew the flight just for fun and no credit.

Can anyone offer help? Everything in Cigar Box looks fine and the flight downloaded just fine.


Misty Flying Club and Multi Player / Re: MFC Tour Completions
« on: October 25, 2018, 05:09:57 PM »
Completed MFC0002 10-25-2018. Pilot Buddy Nix MFC0071

I see the award has been posted.  Thanks Norm


Misty Flying Club and Multi Player / Re: MFC Tour Completions
« on: October 20, 2018, 05:58:34 PM »
Tour MFC0001 Completed 10-20-2018 by Buddy Nix MFC0071

« on: February 03, 2016, 05:59:04 PM »
Try this:  It is the first item in the General Discussion area of the forum for ORBX.

General Discussion / Re: Sky Beams ???
« on: May 24, 2015, 04:36:26 PM »
Hi Marty, this afternoon I was flying in RTMM and saw the same thing and fortunately I was able to get it fixed. Let me know if I can help.


DX10 and Prepar3D Discussions / Owikeno Trip Tic by Doug Linn
« on: March 01, 2015, 05:03:41 PM »
TeeCee and I had a lot of fun this morning flying this Trip Tic. We had been working for quite some time getting Prepar3Dv2.5 installed along with Tongass Fjords, ORBX scenery and all the RTMM libraries and sceneries. But it was well worth it. My old weak Dell computer, 4 years old, ran like a charm producing 20 fps out of max 20 fps on most of the flight with mist, water falls, and all the wonderful RTMM scenery installed. Looked great. Mountains, glaciers, water, rocks, all really fine! Could not say enough about how pleased we were with all of it. Owikeno Lake and that area will be fun to explore for some time to come. Thanks to all with RTMM who had something to do with producing this fantastic area. Just great!

DX10 and Prepar3D Discussions / Re: Missions in P3Dv2
« on: June 17, 2014, 07:56:28 AM »
Jeff, I enjoy the missions you write and I enjoy flying in P3Dv2 so I hope you can make this work. Many thanks for all your efforts and the work you do with RTMM. I am having loads of fun with this combination!

Pages: [1] 2 3 ... 6