Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - roundrobin

Pages: [1] 2 3 ... 10
1
General Discussion / Al Pelletier still around
« on: February 17, 2020, 05:40:32 PM »
Hi friends. I am still very active flying so routes (I still have the installation done in 2013 and it is still working great. I  have never altered it). I haven't been active due to real life happenings. I suffered a blood clot to the heart on Dec 20th and managed to survive it. This place is still the best fun for any flight simmer. I am busy downloading and re-learning installs, as I have an old friend who wants to join. Also that will give me the chance to install it on Prepar 3D-4.  anyway, I read the Forum. A big hello to all from Comox.

2
General Discussion / Re: New maps for Little NavMap
« on: April 15, 2019, 08:24:22 PM »
Thank you so much for putting in all that work. These maps are fantastic!!

3
General Discussion / Re: Missing Friend
« on: December 01, 2018, 05:22:21 PM »
He gave me a lot of help, as most here did. Sorry to hear. I don't know what the average age is in this group. I am in my seventies with lots of health issues.
Have to enjoy every day. But, again, sad news!!

4
General Discussion / Re: Sad News
« on: December 01, 2018, 05:18:42 PM »
That was a terrible tragedy down there. Best wishes to JJ.

al


5
Prepar3D-Version 4 / Re: BWEP repaints
« on: December 07, 2017, 08:25:19 PM »
Thank you for that. Will check it out for sure.


al


6
Prepar3D-Version 4 / Re: BWEP repaints
« on: December 07, 2017, 07:11:56 PM »
Sorry! What is a BWEP ? Brain can't connect  8)

7
Prepar3D-Version 4 / Re: Screen shots from Al
« on: December 06, 2017, 04:28:47 PM »
Great news Al! Like I mentioned, problems like yours are almost always a configuration issue. Aren't you glad you didn't reinstall from scratch out of frustration? And if you had, you'd still have the same, overlooked issue going on. Hopefully someone else reading this thread will learn what you learned.

Steve

Steve
That is why I posted the fix. Someone will stumble into this again. There is a positive about an issue like this is that it got me really dig into Prepar3D V4. Now maybe I can help someone later.
I found that the people here in Misty Mooring have always been so helpful. Jeff, and you and everyone that helped on this (I can't see the names while typing) Thank you.

Still have a lot to learn.
Al

8
Prepar3D-Version 4 / Re: Screen shots from Al
« on: December 06, 2017, 03:03:38 PM »
Hello guys and gals
Problem fixed with the help of Nick and Larry at ORBX. All it was, was the Object Flow not enabled in Prepar3D V4 under addon. Once I enabled and restarted the sim, it was all good.

Thanks to all that helped on this.

Now it's on to Tongass

al

9
Prepar3D-Version 4 / Re: Screen shots from Al
« on: December 05, 2017, 11:52:01 PM »
One question (wild shot). Were those great shots of CAC8 installed with the Prepar3d V4 install?

10
Prepar3D-Version 4 / Re: Screen shots from Al
« on: December 05, 2017, 10:44:56 PM »
Al,

This is what your insertion points should look like:


Thank you Dale. Great reference for me to work on tomorrow, once I start installing RTMM libraries and files.

al

11
Prepar3D-Version 4 / Re: Screen shots from Al
« on: December 05, 2017, 10:42:51 PM »
Al, Just my 2 cents. Reinstalling your sim is almost never a fix for problems like yours. The problems relate to something in the way things are configured. Reinstallation is a radical step to take.


Sorry Steve. Meant to answer this. Have been very busy with the ORBX team. Yes! You are correct. Re-installing wouldn't help me. I agree.

al

12
Prepar3D-Version 4 / Re: Screen shots from Al
« on: December 05, 2017, 10:41:16 PM »
Jeff and All
An update. I spent the day with an ORBX troubleshooting and they are scratching their heads. Everything works fine. Installed Bella Coola (ORBX) and Ketchikan (ORBX) all work great. The Bella Coola scenery is stunning. I took off and flew around the mountains and couldn't believe the depth perception. I am very impressed. So it all works good "EXCEPT" CAC8 and CAG8. Just won't go. There is a little sea plane place and restaurant on Protection Island just south of cac8 (Dinghy Dock Pub. Actually been there). And as per the picture it is all good. Campbell river is good. Just cannot get CAC8. I have my scenery set the way it should be according to ORBX techs. So tomorrow I will start installing some of Misty's stuff and see where that goes. If that works OK, then I don't care if I ever fix my problem. One positive thing about this problem is that it really got me digging into Prepar3D V4. I did reload the ObjectL, uninstalled and re-installed FTX Central3, bought and installed global Vector, openLC NA, CYBD and PAKT.
One favour. Would someone go to that Dinghy Dock Pub and see if you have that huge ferry sitting there.

A couple of pictures of what CAC8 looks right now and Bella Coola as well as the dock just south of CAC8


al

13
Prepar3D-Version 4 / Re: Screen shots from Al
« on: December 05, 2017, 04:40:16 PM »
Thanks Jeff,
Your screen explains it to me. Will fiddle with it today. I'll get there :-)


al

14
Prepar3D-Version 4 / Re: Screen shots from Al
« on: December 04, 2017, 10:34:27 PM »
I looked at your picture and figured out something. I am missing the dock and the point of land where the red car is. Also missing the platform that the big Propane tank is on. So I do have a lot of it, but missing some parts. I also have the large ship in the background. So just missing chunks of it including some terrain. That is very interesting!!!

al


15
Prepar3D-Version 4 / Re: Screen shots from Al
« on: December 04, 2017, 10:27:20 PM »
I think I do. I paid for it and it installed.:-)  I might unload everything and re-install Prepar3D V4.
Copy of my directory included. I tried to get support from ORBX but no luck so far.

Al,

"You many have answered this but do you have Orbx PNW installed?"

This is required for CAC8
[/quote]

Pages: [1] 2 3 ... 10