Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Fred

Pages: [1] 2
1
Great stuff guys  ;D Thanks a million for making this package. Did a manual install and copied the files over to FSX and to P3D. Works just great. Just needed to fix the usual wake problem in P3D.

2
General Discussion / Re: Orbx PFJ Pacific Fjords - Patch 002 released
« on: September 23, 2012, 05:54:34 AM »
I know that CIRP has a very high load, but before the ORBX patch the fps was OK around Stewart with CIRP active. So what I am trying to say is that PFJ SP2 patch made it worse for CIRP. My advice is to look into the CIRP files and see if there is some culprit files.

3
General Discussion / Re: Orbx PFJ Pacific Fjords - Patch 002 released
« on: September 22, 2012, 03:05:01 PM »
Installed and tested out. Big trouble around CSZT Stewart with huge drop in fps, but with CIRP deactivated it is OK

4
Help and Troubleshooting / Misty Moorings boat traffic in P3D
« on: August 24, 2012, 05:27:03 PM »
Hi guys

There seems to be a small problem with the wake effect files on at least one boat in the package.
It points 90 degrees straight up. See the picture.

Haven't found out which boat causing this yet, but looking...

5
Addon Scenery and Enhancements / EZ-1 library file
« on: March 25, 2012, 11:31:10 AM »
Hi guys

I have trouble with low frame rate almost all over in Misty Moorings land. But if I deactivate EZ-1 library everything is just great on fps. What is causing this? I have downloaded the version found on flightsim.com
Does it contains some "bad" files maybe? Anyone else noticed this?


6
Addon Scenery and Enhancements / Re: CIRP is Live!
« on: November 01, 2011, 07:42:28 PM »
Looking forward to many hours flyin' around in this great scenery addon. Excellent work guys.

7
General Discussion / Rwy12 library?
« on: July 09, 2011, 07:40:17 PM »
I see on the scenery page that it is not mentioned you need rwy12 library. Is this obsolete now for you scenery packs or is it just a glitch it is not mentioned among the "need" files?

8
General Discussion / Re: OZx returning to ORBX FTX
« on: May 01, 2011, 08:36:33 AM »
If one should follow this attitude to the fullest all repaints of payware aircrafts should be looked upon the same way.  (ORBX way) But here most of the industry encourage people to make repaints. And why? It benefits them in a positive manner.

9
Addon Scenery and Enhancements / Re: Something I'm working on
« on: April 30, 2011, 07:59:08 AM »
Great stuff. Just love these small places.

10
General Discussion / Re: Development stopped?
« on: April 27, 2011, 06:28:35 PM »
Thanks guys for the replies. I have so far been visiting little more than half of the places so I have much more to look forward to. I must say I enjoy the work done in this area very much. I like the atmosphere you have created here and all the boat traffic are just great.

11
General Discussion / Development stopped?
« on: April 26, 2011, 03:46:55 AM »
Hi Guys

After a landslide with releases of small scenery packages it seems to have stopped completly. Has this something to do with the recent merge of OZx and ORBX? Just wondering.

12
Addon Scenery and Enhancements / Re: Coming soon : JEDWAY BAY SEABASE
« on: April 06, 2011, 07:12:59 PM »
Some problems again here with textures that is missing or maybe in the wriong place. See the picture.

Pls. advice.

Fred

13
I had EZ installed inside addon scenery/ez-lib and that caused the texture not showing. Moved the fbo3 bitmaps to the main texture folder and have now textures on the house up at Bravo airstrip. But it should be not be like that, should it? I have other sceneries that uses EZ and they are perfectly happy with my installation. If I need to duplicate textures all around my fsx setup, it is not making the life easier. Could you scenery designers try to keep things as simple as possible?

14
Addon Scenery and Enhancements / Re: Problems with Kidala scenery
« on: March 16, 2011, 05:25:08 PM »
As I said in another posting here it looks like you need the Rwy12 libraries as well to get the helicopter pads right on the wire.

15
I did.

Pages: [1] 2