Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - briansommers

Pages: [1] 2 3
General Discussion / Pipeline Inspection?
« on: February 06, 2020, 04:24:38 PM »
I'm watching some episodes on YT about doing pipeline inspection.

Is there any scenery that you all make that a person could do that in flightsim?

out by the water, there are a few buildings floating above the ground.

I'm using P3dv4.5 with no hotfixes
Pilots mesh
ORBX Global, vector, SAK, and all of MM addons

anyone else getting this?

General Discussion / Re: Looking for a specific MM scenery...
« on: December 21, 2018, 08:44:02 AM »
mmm. not sure about that.

I'm wondering if it was more like some sort of a company. I remember lots of tanks, water or oil? not sure but a lot of stuff goings on for sure...

I guess I'll have to start flying to every single one!

General Discussion / Looking for a specific MM scenery...
« on: December 20, 2018, 08:31:19 PM »
I know I have it but I can't remember what it was.

I remember it was a land airstrip and on it were a bunch of construction vehicles, lots of stuff going on.

Anyone know by chance which one that could be?

Prepar3D-Version 4 / Re: P3d is changing my MM scenery entry
« on: December 20, 2018, 07:52:37 PM »
boom, that fixed it!
I had looked at that earlier and was a little afraid to do anything for fear I would royally screw it up, but all is good now.

Prepar3D-Version 4 / P3d is changing my MM scenery entry
« on: December 20, 2018, 06:50:35 PM »
In order for me to see the scenery I have to move MM scenery to the top of the list, lower number

then it works fine. but then when I restart it again later it moves it down under all of the orbx stuff like a high number maybe 155 etc. then I have to move it all the way up again.

How do I keep it up?

From Here to There - Missions, Trip Tics and VA / Re: Serenity Aviation
« on: November 02, 2018, 12:25:07 PM »
Your link is still dead.
I would like to see your website.

no its still works. I'm just trying to justify something shiny and new.  ;D

I'm leaning towards Milviz Turbo Otter

is this good for short lake ops or should I be looking elsewhere?


I got everything installed, all the libs, the tester worked good and I got Misty Moorings in  PF20 I also installed the missing cabins.

I'm running P3d v4.3

the amount of scenery is overwhelming are there any recommendations to begin with?

like the "super cool" sceneries, etc.  I don't do that much float flying but I see I'll need to. I'm thinking of getting the Milviz Turbo Otter. I have Carenado Cessna T210M, T206H, 207, 185 (showing its age, now) and a ton other of his stuff, but needing a better amphibian.

General Discussion / Can you service Cabins in the winter?
« on: November 27, 2017, 08:37:35 PM »
I'm starting a VA that uses your missing cabins and other scenery.

I'm striving to create a realistic experience.

Any locals in Alaska, do you know if charter companies would fly passengers out to the local cabins during winter? Or do the cabins pretty much shut down during winter? Hard to imagine tourists that would come out and want to rent a cabin in the winter, but I'm sure it's been done sometime.

Can anyone weigh in on this?

Also, what type of charter flights are there in the Winter, especially in the Juneau area? Or does it all come to a grinding halt?

Prepar3D-Version 4 / Re: Tongass Fjords X crashes FTXCentral
« on: November 15, 2017, 10:08:03 AM »
that's it!


Very tricky. I do that all the time when it comes to the aircraft.cfg files if I want to adjust the brakes or whatever I will always do

2.3//original number here

and it works and runs but not the terrain.cfg
good to know.

Prepar3D-Version 4 / Re: Tongass Fjords X crashes FTXCentral
« on: November 14, 2017, 05:52:37 PM »
OK, I'll try it.

Prepar3D-Version 4 / Tongass Fjords X crashes FTXCentral
« on: November 14, 2017, 05:07:34 PM »
at least on my system it does.

I can repeat this like clockwork.

As soon as put in the entries in my terrain.cfg file and renumber them.
If I start up FTXC it will crash it and it won't run.
as soon as I take those entries out, it works again,

however, even though it does crash FTXC it does WORK in p3d v4.1 just nice and fine, the water is correct and everything, no trees in the ocean.

However, this is a no go for me, because you have to be able to get to FTXC

so, just letting everyone know.

I've installed it twice, repaired it twice

I have checked my terrain.cfg everything is correct
I have assured that the higher/lower priority is correct

still i have trees in my water. no water at all

to even compound matters I can't even run the fsaddon configurator program, just a little white box pops open and thats it.

Any ideas? I guess, it's not meant to happen for me, cause I don't know what is going on.

I installed it with the migration tool, I have win 10 64 bit and p3d v3.3.5

If anyone can help, that would be great.

Pages: [1] 2 3