Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - xxd09

Pages: [1] 2 3 ... 16
1
Addon Scenery and Enhancements / Re: Vertical Wakes
« on: December 09, 2019, 07:15:56 PM »
Thanks Norm-doing a clean new install of P3Dv 4.5 Hotfix2
The contrails appears again and the “coastguard wake fix did not work completely
Not tech enough to run your DOS program
But Ground Decal did the job on the one ship affected
Thanks again
xxd09

2
Help and Troubleshooting / Re: PAVD - BWEP Pipeline Broken
« on: December 09, 2019, 04:52:16 PM »
Gentlemen-I have just done a complete new install of my ZP3D v4.5 plus Hotfix 2 for various reasons-constipation!!!!!
At Valdez the pipeline is intact
Obviously the faults were with my system-a lesson for me
Thanks again for your efforts and fabulous scenery add-ons
xxd09

3
Help and Troubleshooting / Re: Klutina Outfitters
« on: October 09, 2019, 03:55:09 AM »
Thanks for that.Tree appearance in “Winter” mode seems to be a variable for me so not always sure if install has gone by the book!
xxd09

4
Help and Troubleshooting / Klutina Outfitters
« on: October 08, 2019, 03:30:52 AM »
Flying into Klutina with all new RTMM Season Switcher and new Klutina install
Using Winter -I note all is good but Trees round airstrip green compared with surrounding scenery trees-no snow on them.
Is this normal?
Orbyx scenery-P3Dv 4.5
xxd09

5
Help and Troubleshooting / Re: PAVD - BWEP Pipeline Broken
« on: September 26, 2019, 03:59:47 AM »
I can confirm this-Pipeline at PAVD was working perfectly before recent RTMM update
2 steps forward 1 back
Can only agree that all RTMM,s work is much appreciated by all of us and especially by me
xxd09

6
General Discussion / Re: New Orbx FTX Central
« on: September 18, 2019, 03:54:31 AM »
Bit the bullet and installed Orbx Central last night
Followed all the instructions as they arose
All updates done All Sceneries in order
All good
Whew!
xxd09

7
Help and Troubleshooting / Re: BWEP pipeline
« on: September 15, 2019, 10:57:08 AM »
Thanks for that-it was Pilots Mesh 2010 then-disabling it did the trick
I do not have Pilots Mesh installed now
Was 2cm in Display Options -changed to 5cm -no difference
No breaks in pipe after Thompson’s Pass airstrip to Copper Bend .Donnelys Dome Airport pipeline OK
An Orbyx Valdez Scenery anomaly?
xxd09

8
Help and Troubleshooting / BWEP pipeline
« on: September 15, 2019, 06:49:02 AM »
Put in the new RTMM Libraries
Noted that non apposition of pipeline has reappeared at Valdez
Using appropriate library with Orbyx Valdez
I had this a year or two ago and cured it but cannot remember how
Help!
xxd09

9
General Discussion / Re: New Orbx FTX Central
« on: September 13, 2019, 12:38:04 PM »
Orbyx Central v 0.13 released
Appreciate anybody’s experience with this latest Update
xxd09

10
General Discussion / Re: New Orbx FTX Central
« on: September 06, 2019, 11:35:07 AM »
Thanks Dieter-was my gut feeling confirmed by yourself with vastly more experience than me
Are you interested in any of the new Orbyx Sceneries only available via Central 4 ?
I will content myself with the splendid setup I currently have-off to fly the “new” RTMM BWEP “ updates of the Alaska pipeline!
 xxd09

11
General Discussion / Re: New Orbx FTX Central
« on: September 06, 2019, 06:09:07 AM »
Anybody else working with Orbyx Central 4 v0.12?
There seems to have been a lot of updates to the original program over the last few days
I haven’t tried it yet as I have very functional FSX and P3Dv4.5 sims and scared to upset them!
Want new Sceneries though
xxd09

12
General Discussion / Re: BWEP
« on: September 05, 2019, 01:31:00 PM »
Done-thanks
xxd09

13
General Discussion / BWEP
« on: September 05, 2019, 07:15:49 AM »
Updating BWEP Sceneries and all is good
A bit confused re install instructions re“disabling” airports with Orbyx Vector Config tool
I have all Orbyx Scenery in place including PAVD
On BWEP page re BWEP Airports- it shows Package A and B with disabling needed for B
Installation instructions for A seem contradict this
I am confused
Do I or do I not disable PAVD,SAG,5CD,PAPR,1AK1,5BK if I use A?
Apologies if I have misread the required pages
Thanks for all the great work updating
xxd09

14
General Discussion / Re: BWEP readme
« on: August 14, 2019, 02:30:49 AM »
Dieters link worked for me
Thanks-Dieter
xxd09

15
General Discussion / Re: BWEP readme
« on: August 13, 2019, 12:56:47 PM »
Is the Readme now redundant?
xxd09

Pages: [1] 2 3 ... 16