Misty Moorings Forums

Return to Misty Moorings (FSX/P3D/MSFS2020) => Help and Troubleshooting => Topic started by: JDavidPugh on November 07, 2018, 09:48:28 AM

Title: Runway elevation at Wilson River Lodge
Post by: JDavidPugh on November 07, 2018, 09:48:28 AM

Do I have something installed wrong or is there a big dropoff halfway down the runway at Wilson River?
It has effectively cut the runway in half.  Am I missing a BGL to correct this?  Its high enough that I cant taxi to the end of the runway....

Thanks,

David

Title: Re: Runway elevation at Wilson River Lodge
Post by: JDavidPugh on November 07, 2018, 12:38:51 PM

Ok so that is part of the scenery.........
LOL  This should come with a warning sign....

"Caution San Andreas Fault Line"
(http://image-engine.com/wp-content/uploads/2015/08/PROJECT_SAN_RR_100_comp_v001.1222.jpg)

LOL

David

Title: Re: Runway elevation at Wilson River Lodge
Post by: jeff3163 on November 07, 2018, 07:37:35 PM

Hello David.  Welcome to RTMM.  Make sure your mesh slider is at 5m.  Could you show a screenshot of the issue?  Mine looks like this.  No drop-offs I can see ...

(http://i1130.photobucket.com/albums/m531/jeff3163/MOON/Flight%20Simulator%20X%20Files/2018/Prepar3D%202018-11-07%2016-39-55-46.png)

(http://i1130.photobucket.com/albums/m531/jeff3163/MOON/Flight%20Simulator%20X%20Files/2018/Prepar3D%202018-11-07%2016-31-44-06.png)

Title: Re: Runway elevation at Wilson River Lodge
Post by: eagleman on April 21, 2019, 07:36:38 PM

I am running P3D V4 and also find a large dip in the middle of the runway.  Even going slow it will flip my plane.  I have my mesh set to 5m.  Has there been any workaround?

Title: Re: Runway elevation at Wilson River Lodge
Post by: jeff3163 on April 21, 2019, 09:15:29 PM

Hi,
     This thread is from last November, and we haven't heard back from David about his issue.  A screenshot helps a lot.   ;)  Post a shot of the dip, please.   :D

(Welcome to RTMM, the forum, btw   :) )

Title: Re: Runway elevation at Wilson River Lodge
Post by: eagleman on April 22, 2019, 07:17:32 PM

If I put my mesh at 19cm or higher it is flyable.  Anything lower and it is not flyable.  The change in elevation appears to be about 2 ft

Title: Re: Runway elevation at Wilson River Lodge
Post by: jeff3163 on April 22, 2019, 09:24:16 PM

 :o
     I discovered that there is an invisible "platform" near the windsock in the runway.  A raised area of about 2 or 3 meters square and maybe a few inches to half a foot off the ground.  I can roll over it easily in my beaver.  But it pops me up a bit, and causes skidmarks to appear.   :o ;D :D

I am sitting still in these shots, parked on an invisible "platform".   ???
(https://oi1130.photobucket.com/albums/m531/jeff3163/MOON/Flight%20Simulator%20X%20Files/2019/Prepar3D%202019-04-22%2018-00-34-92.png)(https://oi1130.photobucket.com/albums/m531/jeff3163/MOON/Flight%20Simulator%20X%20Files/2019/Prepar3D%202019-04-22%2018-01-27-11.png)(https://oi1130.photobucket.com/albums/m531/jeff3163/MOON/Flight%20Simulator%20X%20Files/2019/Prepar3D%202019-04-22%2018-00-58-66.png)

Title: Re: Runway elevation at Wilson River Lodge
Post by: Dieter on April 23, 2019, 05:32:52 AM

I confirm Jeff's observation.
(The scenery wasn't part of the "Refresh Campaign 2019" up to now.)